MS Lively Power Supply is powerful enough to perform horizontal and vertical electrophoresis as well as two-dimensional electrophoresis SDS-PAGE applications. In addition, it can operate with a fully programmable mode and offer up to 6 multi-step setting conditions. The 2.4” TFT-LCD colored screen also allows you to see all the running/setting conditions while operating. For those beginners in electrophoresis, the built-in data for some typical running conditions could be extremely helpful. All 3 models are designed with great safety features to ensure the safety of the lab and experiment.
Electrophoresis Power Supply
Lively 500V Power Supply, MP-510
Description
Features
Specification
Documents
Description
Features
- Four pairs of output terminals
- 2.4” TFT-LCD colored screen shows all parameters during operation
- Timer with alarm function
- Compact size with stackable case
- Constant voltage/ current/ power operation mode
- Typical Running condition helps electrophoresis beginner
- Wide application for Western blotting, semi-dry blotting, DNA/RNA and protein electrophoresis
- Advanced safety device design
- Universal rated voltage for worldwide distributions
Specification
| Cat. No. | MP-510 |
|---|---|
| Output Voltage / Inc | 5 – 500 / 1V |
| Output Current / Inc | 1 – 800mA / 10mA |
| Power | 300W |
| Rated Voltage | 100-240V~: 47-60Hz |
| Type of Output | 1. Voltage or Current with automatic crossover 2. When target constant mode is set, system automatically adjusts the two other parameter to maximum to allow constant run (later could be changed by user) |
| Program Storage | 30 programmed files |
| Program Multi-Step | Up to 6 steps |
| Editable Program Function | 1.Typical running conditions program 2.Manual editable program |
| Display | 2.4” TFT |
| Control | Microprocessor controller |
| Safety Device | No Load detect |
| Leakage detect | |
| Over temperature protection | |
| Over load detection | |
| Sudden load change detection(could be enabled by proper setting) | |
| Shrouded plugs and sockets | |
| Timer | Constant: 9999 (min) with alarm/ Continuous Program: 999 (min) with alarm/ Continuous |
| Crossover | Yes |
| Stackable | Yes |
| Automatic Recovery After Power Failure | Yes |
| Operating Temperature | 4℃~ 40℃ |
| Material | PC housing and flame retardant ABS faceplate |
| Dimension | Approx. 8.5″x13.2″x4.1″ (215 x 335 x 104 mm) |
| Weight | Approx. 4.6lb (2.1 kg) |
Documents
Lively 3AP Power Supply, MP-320
Description
Features
Specification
Documents
Description
Major Science offers 3 models of gel electrophoresis power supplies constructed with microprocessor controller and 4 pairs of outlet terminals which covers the broadest range of application in general laboratory. The microprocessor control can perform either continuous or timed output, and user is able to pause and resume anytime without resetting the timer.
MS Lively Power Supply is power enough to perform horizontal and vertical electrophoresis as well as two-dimensional electrophoresis SDS PAGE applications. In addition, it can operate with a fully programmable mode and offer up to 6 multi-step setting conditions. The 2.4” TFT-LCD colored screen also allows you to see all the running/setting conditions while operating. For those beginners in electrophoresis, the built-in data for some typical running condition could be extremely helpful. All 3 models are designed with great safety features to ensure safety of the lab and experiment.
Features
- Four pairs of output terminals
- 2.4” TFT-LCD colored screen shows all parameters during operation
- Timer with alarm function
- Compact size with stackable case
- Constant voltage/ current/ power operation mode
- Typical Running condition helps electrophoresis beginner
- Wide application for Western blotting, semi-dry blotting, DNA/RNA and protein electrophoresis
- Advanced safety device design
- Universal rated voltage for worldwide distributions
Specification
| MP-320 | |
| Output Voltage / Inc | 5 – 300 / 1V |
|---|---|
| Output Current / Inc | 10 – 3,000mA / 10mA |
| Power | 300W |
| Rated Voltage | 100-240V~: 47-60Hz |
| Type of Output | 1. Voltage or Current with automatic crossover 2. When target constant mode is set, system automatically adjusts the two other parameter to maximum to allow constant run (later could be changed by user) |
| Program Storage | 30 programmed files |
| Program Multi-Step | Up to 6 steps |
| Editable Program Function | 1.Typical running conditions program 2.Manual editable program |
| Display | 2.4” TFT |
| Control | Microprocessor controller |
| Safety Device | No Load detect |
| Leakage detect | |
| Over temperature protection | |
| Over load detection | |
| Sudden load change detection(could be enabled by proper setting) | |
| Shrouded plugs and sockets | |
| Timer | Constant: 9999 (min) with alarm/ Continuous Program: 999 (min) with alarm/ Continuous |
| Crossover | Yes |
| Stackable | Yes |
| Automatic Recovery After Power Failure | Yes |
| Operating Temperature | 4℃~ 40℃ |
| Material | PC housing and flame retardant ABS faceplate |
| Dimension | Approx. 8.5″x13.2″x4.1″ (215 x 335 x 104 mm) |
| Weight | Approx. 4.6lb (2.1 kg) |
Documents
Lively 300V Power Supply, MP-310
Description
Features
Specification
Documents
Description
Major Science offers 3 models of electrophoresis power supplies constructed with microprocessor controller and 4 pairs of outlet terminals which covers the broadest range of application in general laboratory. The microprocessor control can perform either continuous or timed output, and user is able to pause and resume anytime without resetting the timer.
MS Lively Power Supply is power enough to perform horizontal and protein electrophoresis as well as two dimensional electrophoresis SDS PAGE applications. In addition, it can operate with a fully programmable mode and offer up to 6 multi-step setting conditions. The 2.4” TFT-LCD colored screen also allows you to see all the running/setting conditions while operating. For those beginners in electrophoresis, the built-in data for some typical running condition could be extremely helpful. All 3 models are designed with great safety features to ensure safety of the lab and experiment.
Features
- Four pairs of output terminals
- 2.4” TFT-LCD colored screen shows all parameters during operation
- Timer with alarm function
- Compact size with stackable case
- Constant voltage/ current/ power operation mode
- Typical Running condition helps electrophoresis beginner
- Wide application for Western blotting, semi-dry blotting, DNA/RNA and protein electrophoresis
- Advanced safety device design
- Universal rated voltage for worldwide distributions
Specification
| Cat. No. | MP-310 |
|---|---|
| Output Voltage / Inc | 5 – 300V / 1V |
| Output Current / Inc | 1 – 700mA / 1mA |
| Power | Input:200W; Output: 150W |
| Rated Voltage | 100-240V~; 47-60Hz |
| Type of Output | 1. Voltage or Current with automatic crossover 2. When target constant mode is set, system automatically adjusts the two other parameter to maximum to allow constant run (later could be changed by user) |
| Program Storage | 30 programmed files |
| Program Multi-Step | Up to 6 steps |
| Editable Program Function | 1.Typical running conditions program 2.Manual editable program |
| Display | 2.4” TFT |
| Control | Microprocessor controller |
| Safety Device | No Load detect |
| Leakage detect | |
| Over temperature protection | |
| Over load detection | |
| Sudden load change detection(could be enabled by proper setting) | |
| Shrouded plugs and sockets | |
| Timer | Constant: 9999 (min) with alarm/ Continuous Program: 999 (min) with alarm/ Continuous |
| Crossover | Yes |
| Stackable | Yes |
| Automatic Recovery After Power Failure | Yes |
| Operating Temperature | 4℃~ 40℃ |
| Material | PC housing and flame retardant ABS faceplate |
| Dimension | Approx. 8.5″x13.2″x4.1″ (215 x 335 x 104 mm) |
| Weight | Approx. 4.6lb (2.1 kg) |
Documents
Handy 100V Power Supply, MP-100
Description
Features
Specification
Documents
Description
The Handy 100V Power Supply is specifically designed for DNA and RNA electrophoresis. It allows two constant voltages of either 50V or 100V. The low cost, light weight and small foot print make it perfect for teaching labs as well as routine electrophoresis use. It can be purchased individually or in packages with horizontal gel electrophoresis systems for economical purposes.
Features
- 50V or 100V constant voltage output
- 400mA maximum current
- 40W maximum power
- Safety device
- Ultra compact size
- Developed specifically for DNA and RNA electrophoresis
- Great value at very competitive pricing
- Bundled package with MJ-105A and MT-108
Specification
| Cat. No. | MP-100 |
|---|---|
| Output Voltage / Inc | 50V/ 100V |
| Output Current / Inc | 400mA |
| Output power | 40W |
| Output Type | Constant voltage |
| Voltage selection | 50V and 100V |
| Safety device | No-load detection; shrouded plugs and sockets |
| Operation temperature | 4° – 40° |
| Dimension (WxLxH) | 2.4″x1.6″x4.7″ (60x40x120mm) |
| Terminal pairs | 1 pair |
| Material | Polycarbonate (PC) |
| Weight | Approx. 0.7lb (0.3kg) |
| Rated voltage | 100 – 120V ~ only |
Documents
Mini Pro 500V Power Supply, MINI-500
Description
Features
Specification
Documents
Description
Featuring in small size and versatility, the newly designed Mini Pro 500V gel electrophoresis apparatus is an ideal choice for researchers. Capable of providing constant voltage or current in 1V or 1mA increment, the unit is perfectly suitable to run both vertical polyacrylamide or horizontal agarose gel electrophoresis experiments. Continuous or timed operation can be easily set up with the simple and user-friendly interface. Moreover, the upgraded 2-step programmable function is more practical for protein electrophoresis. Mini Pro 500V is featured with 2 electrode pairs, allowing 2 gels to be run simultaneously, saving both time and valuable bench space. With a universal voltage rating, Mini Pro 500V is also designed and constructed to the most rigorous safety standards.
Features
- Constant voltage or constant current operation
- 1V increment voltage control; 1mA increment current control
- Max 500V, 400mA and 120W for Mini Pro 500V
- Two pairs of outlet terminals
- Timer with alarm function
- Safety device
- Compact size and lightweight
- Competitive pricing choice
- 2-step programmable control
Specification
| Cat. No. | MINI-500 |
|---|---|
| Output Voltage / Inc | Step1: 10 – 500V / 1V |
| Step2: 10 – 500V / 1V | |
| Output Current / Inc | Step1: 1 – 400mA / 1mA |
| Step2: 1 – 400mA / 1mA | |
| Max. Watt | 120W |
| Output Type | Constant voltage or constant current |
| Control | Microprocessor controller |
| Terminal Pairs | 2 pairs |
| Timer | 999 (min) with alarm/ Continuous (set=0) |
| Safety Device | No load detection; shrouded plugs and sockets |
| Operation Temperature | 4℃-40℃ |
| Dimension | 140 x 191 x 84mm (W x L x H) |
| Material | Polycarbonate housing and aluminum base plates |
| Weight | Approx. 1 kg |
| Rated Voltage | 100 – 240 V~, 50-60Hz, 2.5A |
| Program | 2-STEP Program |
| Presetting value | STEP1 (V: 500 V; A: 16 mA; T: 30 min) |
| STEP2 (V: 500 V; A: 24 mA; T: 240 min) | |
| *If voltage or current is set 0 in step 2, system will not proceed to step 2. | |
| *if time is set 0, system will keep running until user manually stops. | |
| Certification | ETL, CE, FCC |
Documents
Mini Pro 300V Power Supply, MINI-300
Description
Features
Specification
Documents
Description
Featuring in small size and versatility, the newly designed Mini Pro 300V / 500V electrophoresis system is an ideal choice for researchers. Capable of providing constant voltage or current in 1V or 1mA increment, the unit is perfectly suitable to run both vertical polyacrylamide or horizontal agarose gel electrophoresis experiments. Continuous or timed operation can be easily set up with the simple and user-friendly interface. Moreover, the upgraded 2-step programmable function is more practical for protein electrophoresis. Mini Pro 300V and 500V both are featured with 2 electrode pairs, allowing 2 gels to be run simultaneously, saving both time and valuable bench space. With a universal voltage rating, Mini Pro 300V and 500V are also designed and constructed to the most rigorous safety standards.
Features
- Constant voltage or constant current operation
- 1V increment voltage control; 1mA increment current control
- Max 300V, 400mA and 60W for Mini Pro 300V
- Two pairs of outlet terminals
- Timer with alarm function
- Safety device
- Compact size and lightweight
- Competitive pricing choice
- Packages with midi sized horizontal electrophoresis systems and vertical electrophoresis systems
- 2-step programmable control
Specification
| Cat. No. | MINI-300 |
|---|---|
| Output Voltage / Inc | Step1:10 – 300V / 1V |
| Step2: 10 – 300V / 1V | |
| Output Current / Inc | Step1:10 – 400mA / 1mA |
| Step2: 10 – 400mA / 1mA | |
| Max. Watt | 60W |
| Output Type | Constant voltage or constant current |
| Control | Microprocessor controller |
| Terminal Pairs | 2 pairs |
| Timer | 999 (min) with alarm/ Continuous (set=0) |
| Safety Device | No load detection; shrouded plugs and sockets |
| Operation Temperature | 4℃-40℃ |
| Dimension | Approx. 5.5″x7.5″x3.3″ (140 x 191 x 84mm) |
| Material | Polycarbonate housing and aluminum base plates |
| Weight | Approx. 2.2lb (1 kg) |
| Rated Voltage | 100 – 240 V~, 50-60Hz, 2A |
| Program | 2-STEP Program |
| Presetting value | STEP1 (V: 300 V ; A: 16 mA; T: 15 Min) |
| STEP2 (V: 300 V; A: 24 mA; T: 120 min) | |
| *If voltage or current is set 0 in step 2, system will not proceed to step 2. | |
| *if time is set 0, system will keep running until user manually stops. |
Documents
